| TYP |
Email pre interiérové dekoračné nátery |
| PRÍKLADY POUŽITIA |
Vytváranie dekorácií, ornamentov na natretom dreve alebo kove, dekoračných objektoch alebo stenách |
|
| TECHNICKÉ ÚDAJE |
|
|
| Rozsah odtieňov |
Zlato, Striebro, Meď
|
| Stupne lesklosti |
perleťový |
| Výdatnosť |
10-13 m2/l
10-13 mo/l
|
| Veľkosti balenia |
0.1 l (možné zabezpečiť aj 1,0l balenie)
|
| Riedidlo |
Spray Thinner 1032 |
| Pomer miešania |
Conventional spray application:
-nozzle of 1,4 -1,8 mm
-thin 20-25 vol. % |
| Aplikačná metóda |
Brush, conventional spraying or roller (short pile mohair roller)
|
| Doba schnutia pri 23°C a 50% relatívnej vlhkosti vzduchu |
Dust dry in 1 hour, through dry in 24 hours. |
| Špeciálna vlastnosť |
|
| Odolnosť voči umývaniu |
Light wiping with a damp rag |
| Solids volume |
30% |
| Hustota |
Approximately 0,9 -1,2 kg/l, ISO 2811 |
| Skladovanie |
Approximately 0,9 -1,2 kg/l, ISO 2811 |
| Kód produktu |
211_6001 |
|
| NÁVOD NA POUŽITIE |
| Podmienky aplikácie |
The surface must be thoroughly dry. The temperature of the air, paint and the surface should be at least 10 °C, and the relative humidity of the air below 80 % during application and drying. |
| Príprava |
Unpainted surfaces:
Clean dirt, dust, grease, oil and rust.
Wood, wood fibre board and card board surfaces are primed even and compact 1-2 times with Otex primer tinted to a colour matching with the top coat colour (Gold –TVT X029, SIlver TVT h168, Copper TVT J123). Metal surfaces in dry interior premises can be painted directly with Miranol Decoration Paint. Aluminium surfaces must be roughened before priming.
Previously painted surfaces:
Wash down previously painted surfaces with Cleaning Agent (Maalipesu) and rinse carefully with water. Remove loose, flaking paint with a scraper and sand hard, glossy and industrial painted surfaces. Remove sanding dust. Fill holes and cracks with Spakkeli Alkyd putty and sand the filled parts. Prime wooden surfaces with Otex primer tinted to a colour matching with the top coat colour (Gold –TVT X029, SIlver TVT h168, Copper TVT J123). Prime metal surfaces with light grey Rostex Super. |
| Natieranie |
Stir paint well before and during use to avoid the colourfullness caused by the setting of the metalpigments. If needed, thin paint with White Spirit 1050 or with Spray Thinner 1032. Spread the paint with a roller or a brush 1-2 times.
An even finish for large areas can be obtained by rolling or using spray application. Use superlon-spong rubber for corners and angles when using brush application. |
| Čistenie náradia |
Clean tools with White Spirit 1050 or with Tikkurila Pensselipesu (Tool cleaner) |
| Inštrukcie pre údržbu |
Earliest after one month after painting: Clean dirty surfaces with a neutral dishwashing agent (pH 6-8) using for example a sponge or damp cloth. For very dirty surfaces use weak alkaline detergent solution (pH 8-10) using a mop, sponge or damp cloth. Do not leave the surface wet after cleaning. For diluting the detergent solution follow the instructions of the producer.
The surface achieves its final hardness after one month under normal conditions, therefore the surface should be handled carefully during that time. Use smooth brush, damp cloth or mop to clean the surface, if it is necessary. |
| Údržba |
Surfaces painted with Miranol Decoration Paint can be maintenance painted with a same kind of enamel paint or e.g. alkyd paint. See instruction from "pretreatment". |
